#LinelocationError(s)
0.%
1.O2291G28 X0 Y0 Z0
2.(T1 - MILL FACE 2inch facemill)G28 X0 Y0 Z0
3.G0 G17 G20 G40 G49 G80 G90G28 X0 Y0 Z0
4.T1 M6G28 X0 Y0 Z0
5.S1800 M3G28 X0 Y0 Z0
6.G0 G54 X-2. Y-1.G54 X-2 Y-1 Z0
7.G43 H1 Z1.G54 X-2 Y-1 Z1
8.G1 Z0.1 F7.G54 X-2 Y-1 Z0.1
9.(MILL TOP)G54 X-2 Y-1 Z0.1
10.G1 Z0G54 X-2 Y-1 Z0
11.G0 Y.5G54 X-2 Y0.5 Z0
12.G1 X4.G54 X4 Y0.5 Z0
13.G0 Y1.5G54 X4 Y1.5 Z0
14.G1 X-2.G54 X-2 Y1.5 Z0
15.(END)G54 X-2 Y1.5 Z0
16.G0 Z1. M5G54 X-2 Y1.5 Z1
17.G0 G28 G49 G90 Z0G28 X-2 Y1.5 Z0
18.X0 Y0G28 X0 Y0 Z0
19.(DONE)G28 X0 Y0 Z0
20.
21.(T2 - General milling 3/4 INCH, 4-FLUTE FLAT ENDMILL)G28 X0 Y0 Z0
22.G0 G17 G20 G40 G49 G80 G90G28 X0 Y0 Z0
23.T2 M6G28 X0 Y0 Z0
24.S2000 M3G28 X0 Y0 Z0
25.G0 G54 X-2. Y-1.G54 X-2 Y-1 Z0
26.G43 H2 Z1.G54 X-2 Y-1 Z1
27.G1 Z0.1 F12.G54 X-2 Y-1 Z0.1
28.(MILL Profile - rough)G54 X-2 Y-1 Z0.1
29.G1 Z-.59G54 X-2 Y-1 Z-0.59
30.G0 X.01G54 X0.01 Y-1 Z-0.59
31.G41 Y-0.999 D2G54 X0.01 Y-0.999 Z-0.59
32.G1 Y2.01G54 X0.01 Y2.01 Z-0.59
33.G1 X2.01G54 X2.01 Y2.01 Z-0.59
34.G1 Y-0.1G54 X2.01 Y-0.1 Z-0.59
35.G1 X-2.G54 X-2 Y-0.1 Z-0.59
36.(mill profile - finish)G54 X-2 Y-0.1 Z-0.59
37.G1 Z-.6G54 X-2 Y-0.1 Z-0.6
38.G1 Y-1.G54 X-2 Y-1 Z-0.6
39.G1 X0G54 X0 Y-1 Z-0.6
40.G1 Y2.G54 X0 Y2 Z-0.6
41.G1 X2.G54 X2 Y2 Z-0.6
42.G1 Y0.G54 X2 Y0 Z-0.6
43.G1 X-2.G54 X-2 Y0 Z-0.6
44.(mill lower area - angle)G54 X-2 Y0 Z-0.6
45.G1 Z-.19G54 X-2 Y0 Z-0.19
46.G1 Y3. F25.G54 X-2 Y3 Z-0.19
47.G1 X.32G54 X0.32 Y3 Z-0.19
48.G1 Y2. F12.G54 X0.32 Y2 Z-0.19
49.G1 X.5616 Y.63 (10 deg. angle)G54 X0.5616 Y0.63 Z-0.19
50.G1 X2.9G54 X2.9 Y0.63 Z-0.19
51.G40G54 X2.9 Y0.63 Z-0.19
52.(mill lower area - square)G54 X2.9 Y0.63 Z-0.19
53.G0 X3.G54 X3 Y0.63 Z-0.19
54.G0 Y1.5G54 X3 Y1.5 Z-0.19
55.G1 X.975G54 X0.975 Y1.5 Z-0.19
56.G1 Y2.G54 X0.975 Y2 Z-0.19
57.G1 X3.G54 X3 Y2 Z-0.19
58.(rapid to circmill location)G54 X3 Y2 Z-0.19
59.G0 Z.1G54 X3 Y2 Z0.1
60.G0 X.875 Y1.G54 X0.875 Y1 Z0.1
61.(Interpolating large circle)G54 X0.875 Y1 Z0.1
62.G41 X1. D10G54 X1 Y1 Z0.1
63.G01 Z-.19 F12.G54 X1 Y1 Z-0.19
64.G03 X1. Y1. I-.5G54 X1 Y1 Z-0.19
65.G01 X.875 Z.1G54 X0.875 Y1 Z0.1
66.G40G54 X0.875 Y1 Z0.1
67.G00 X-2. Y-1.G54 X-2 Y-1 Z0.1
68.(end)G54 X-2 Y-1 Z0.1
69.G00 Z1. M05G54 X-2 Y-1 Z1
70.G40G54 X-2 Y-1 Z1
71.G00 G28 G49 G90 Z0G28 X-2 Y-1 Z0
72.X0 Y0G28 X0 Y0 Z0
73.(done)G28 X0 Y0 Z0
74.
75.(T3 - CENTERDRILL 5 HOLES .1 DEEP, #3 CENTERDRILL.)G28 X0 Y0 Z0
76.G0 G17 G20 G40 G49 G80 G90G28 X0 Y0 Z0
77.T3 M6G28 X0 Y0 Z0
78.S4000 M3G28 X0 Y0 Z0
79.G0 G54 X-2. Y-1.G54 X-2 Y-1 Z0
80.G43 H3 Z1.G54 X-2 Y-1 Z1
81.G1 Z0.1 F20.G54 X-2 Y-1 Z0.1
82.(BODY)G54 X-2 Y-1 Z0.1
83.(upper 2 holes)G54 X-2 Y-1 Z0.1
84.G81 F16. R0.1 X.31 Y.31 Z-0.1G54 X0.31 Y0.31 Z-0.1
85.X1.69 Y.31G54 X1.69 Y0.31 Z-0.1
86.G80G54 X1.69 Y0.31 Z-0.1
87.G81 F16. R0.1 X.69 Y1.69 Z-.29G54 X0.69 Y1.69 Z-0.29
88.X1.69 Y1.69G54 X1.69 Y1.69 Z-0.29
89.X.875 Y1.G54 X0.875 Y1 Z-0.29
90.G80G54 X0.875 Y1 Z-0.29
91.(END)G54 X0.875 Y1 Z-0.29
92.G0 Z1. M5G54 X0.875 Y1 Z1
93.G0 G28 G49 G90 Z0G28 X0.875 Y1 Z0
94.X0 Y0G28 X0 Y0 Z0
95.(DONE)G28 X0 Y0 Z0
96.
97.(T4 - .5/16 drillbit)G28 X0 Y0 Z0
98.G00 G17 G20 G40 G49 G80 G90G28 X0 Y0 Z0
99.T4 M06G28 X0 Y0 Z0
100.S4000 M03G28 X0 Y0 Z0
101.G00 G54 X-1. Y-1.G54 X-1 Y-1 Z0
102.G43 H4 Z1.G54 X-1 Y-1 Z1
103.G01 Z.1 F20.G54 X-1 Y-1 Z0.1
104.
105.(body)G54 X-1 Y-1 Z0.1
106.G83 F12. P.1 Q.1 R.1 X.875 Y1. Z-1.3G54 X0.875 Y1 Z-1.3
107.G80G54 X0.875 Y1 Z-1.3
108.(end)G54 X0.875 Y1 Z-1.3
109.G00 Z1. M05G54 X0.875 Y1 Z1
110.G40G54 X0.875 Y1 Z1
111.G00 G28 G49 G90 Z0G28 X0.875 Y1 Z0
112.X0 Y0G28 X0 Y0 Z0
113.(done)G28 X0 Y0 Z0
114.
115.M1 (optional stop for deburring hole)G28 X0 Y0 Z0
116.
117.(T6 - tap 2 holes through [1.0" deep] 3/8 16)G28 X0 Y0 Z0
118.G00 G17 G20 G40 G49 G80 G90G28 X0 Y0 Z0
119.T6 M06G28 X0 Y0 Z0
120.S400 M03G28 X0 Y0 Z0
121.G00 G54 X-2. Y-1.G54 X-2 Y-1 Z0
122.G43 H6 Z1.G54 X-2 Y-1 Z1
123.G01 Z.1 F20.G54 X-2 Y-1 Z0.1
124.G84 F25. R.1 J2 X.875 Y1. Z-1.0G54 X0.875 Y1 Z-1
125.G80G54 X0.875 Y1 Z-1
126.(end)G54 X0.875 Y1 Z-1
127.G00 Z1. M05G54 X0.875 Y1 Z1
128.G40G54 X0.875 Y1 Z1
129.G00 G28 G49 G90 Z0G28 X0.875 Y1 Z0
130.X0 Y0G28 X0 Y0 Z0
131.(done)G28 X0 Y0 Z0
132.
133.(T5 - .something drillbit)G28 X0 Y0 Z0
134.G00 G17 G20 G40 G49 G80 G90G28 X0 Y0 Z0
135.T5 M06G28 X0 Y0 Z0
136.S4000 M03G28 X0 Y0 Z0
137.G00 G54 X-1. Y-1.G54 X-1 Y-1 Z0
138.G43 H5 Z1.G54 X-1 Y-1 Z1
139.G01 Z.1 F20.G54 X-1 Y-1 Z0.1
140.
141.(body)G54 X-1 Y-1 Z0.1
142.G83 F12. P.1 Q.1 R.1 X.31 Y.31 Z-1.3G54 X0.31 Y0.31 Z-1.3
143.X1.69 Y.31G54 X1.69 Y0.31 Z-1.3
144.X.69 Y1.69G54 X0.69 Y1.69 Z-1.3
145.X1.69 Y1.69G54 X1.69 Y1.69 Z-1.3
146.G80G54 X1.69 Y1.69 Z-1.3
147.(end)G54 X1.69 Y1.69 Z-1.3
148.G00 Z1. M05G54 X1.69 Y1.69 Z1
149.G40G54 X1.69 Y1.69 Z1
150.G00 G28 G49 G90 Z0G28 X1.69 Y1.69 Z0
151.X0 Y0G28 X0 Y0 Z0
152.(done)G28 X0 Y0 Z0
153.
154.(T7 - Chamfer holes - 90deg chamfer tool, 3/4")G28 X0 Y0 Z0
155.G00 G17 G20 G40 G49 G80 G90G28 X0 Y0 Z0
156.T7 M06G28 X0 Y0 Z0
157.S1600 M03G28 X0 Y0 Z0
158.G00 G54 X-2. Y-1.G54 X-2 Y-1 Z0
159.G43 H7 Z1.G54 X-2 Y-1 Z1
160.G01 Z.1 F12.G54 X-2 Y-1 Z0.1
161.
162.(Chamfer 2X counterbore)G54 X-2 Y-1 Z0.1
163.G81 F12. R.1 X.31 Y.31 Z-.235 (change)G54 X0.31 Y0.31 Z-0.235
164.X1.69 Y.31G54 X1.69 Y0.31 Z-0.235
165.G80G54 X1.69 Y0.31 Z-0.235
166.G81 F12. R.1 X.69 Y1.69 Z-.425 (change)G54 X0.69 Y1.69 Z-0.425
167.X1.69 Y1.69G54 X1.69 Y1.69 Z-0.425
168.G80G54 X1.69 Y1.69 Z-0.425
169.
170.(end)G54 X1.69 Y1.69 Z-0.425
171.G00 Z1. M05G54 X1.69 Y1.69 Z1
172.G00 G28 G49 G90 Z0G28 X1.69 Y1.69 Z0
173.X0 Y0G28 X0 Y0 Z0
174.(done)G28 X0 Y0 Z0
175.
176.M30G28 X0 Y0 Z0
177.%
letternumberpercentcommentoutofboundserrorbg